This standard is issued under the fixed designation A /A M; the 1 This specification is under the jurisdiction of ASTM Committee A ASTM A/AM: Standard Specification for Steel, Sheet and Strip, Heavy- Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural. Find the most up-to-date version of ASTM A at Engineering
|Country:||Trinidad & Tobago|
|Published (Last):||7 February 2006|
|PDF File Size:||6.62 Mb|
|ePub File Size:||16.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
The zstm listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. It is included for that purpose only. Approved May 1, Approved March 1, They must not be overheated during cutting to the extent of causing decarburization.
However, unless the order speci? The analysis shall be from a test sample preferably taken during the pouring of the heat or cast. Within the text, the SI units are shown in brackets. Or if you don’t have an account with us yet, then click here to register. The ability of manufacturers to meet the maximum coil weights depends upon individual mill equipment.
Within the text, the SI units are shown in brackets. The several determinations of any element in a cast shall not vary both above and below the speci?
AK Steel ASTM A and A Hot Rolled Carbon Steel, Structural Steel (SS)
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. MatWeb is intended for personal, non-commercial use. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Note 1—The term weight is used when inch-pound units are zstm standard. Therefore, users must analyze chips taken from the steel in the condition in which it is received from the steel manufacturer.
Such a deviation is obtained by placing an 8-ft straightedge on the concave side and measuring the greatest distance between the strip edge and the straightedge.
NOTE 1—Heavy-thickness edge cutting results in a bevelled edge. Hot-rolled heavy thickness coils 12 in. NOTE 3—The industry de?
Size Limits, Coils Only. If after conducting two resampling efforts, the material does not satisfy the speci?
Property Data This page displays only the text of a material data sheet. Structural steel may be ordered when the coils are intended for conversion to plate steels. Over Over Over Over Over Over Over Over Over Over Over Over Over Over 12 14 17 19 21 24 26 28 35 50 60 65 70 80 to to to to to to to to to to to to to 14, 17, 19, 21, 24, 26, 28, 35, 50, 60, 65, 70, 80, incl incl incl incl incl incl incl incl incl incl incl incl incl Tolerance Over Speci?
Such a deviation is measured by placing a straightedge on the concave side and measuring the greatest distance between the sheet edge and a65 straightedge. Login to see your most recently viewed materials here. Packaging and Package Marking The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values.
ASTM A635 Grade 1018
Please contact us at webmaster matweb. Dimensions and Tolerances 8.
Over 8 to 12, incl Speci? For strip over 8 in. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This table adtm not apply to the uncropped ends of mill edge coils.
The tip of the spindle shall be? Combining values from the two systems may result in non-conformance with the standard. Micrometers with pointed tips are not suitable for thickness measurements. However, under SI, the preferred term is mass. Steels may or may not be subjected to tension test requirement. For nominal thickness, the tolerance is divided equally over and under.
In the event that the manufacturer is dissatis? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.