Real-time pricing, availability & fast worldwide shipping on the BST International EKR Buy online now or contact us for manuals or pdfs. Buy New or Surplus BST EKR (DISCONTINUED BY MANUFACTURER, COMBI WEB GUIDING CONTROLLER, /VAC, 50/60HZ) parts. Radwell. Manuals. A. AUTONICS TZ4ST/TZ4SP SERIES TEMPERATURE CONTROLLER. B. BST EKR – WEB GUIDE. H. HEIDENHAIN – ROTARY.
|Published (Last):||11 October 2012|
|PDF File Size:||4.61 Mb|
|ePub File Size:||2.29 Mb|
|Price:||Free* [*Free Regsitration Required]|
The not used connection piece S2 will be always unlocked. When operation at open unit is necessary, only protection class IP20 is present.
Dither ON hydraulic actuator? Strip the lead ends eventually, use protective lugs and wire according to connection diagram. The compact design of all BST eltromat controllers facilitates the direct janual to or in your guiding device or machine. The disposal of which is subject to the relevant legal rules and regulations. If the unit is not incorporated immediately, please storage it in a non-moistured room until mounting.
Controllers: BST eltromat International
Connection of components according connection plan Installation of EMC-wiring see point 4. Responsible With connected FVG During shifting of guiding point via arrow keys a limit stop was reached. If the servo component is moving into t the final position, DIL switch S1. Displacement of the web will be stopped.
Preselect er sensors 3. Remove material from both sensors and clean the lenses! After the connected components are selected in the set-up menu, all relevant control parameters are largely automatically adjusted. Dither OFF hydraulic actuator? The motor will be switched off without cutout. The procedure used has to be defined by the OEM. Connection of remote control according connection plan if present 6.
Do not connect BS with the connections S1, S2. Remedy actuate shifting into opposite direction LEDs at the commander are blinking as follows: Correct in case of deviation. De-commissioning De-commissioning scrapping of the guiding system must carry out only together with the complete unit. Remove the cover plate with the cable gland and pull out the PCB?
Through a target-performance comparisonBST eltromat controllers ensure that the material being processed manyal exactly at its intended position.
This amplifier could be used for – web edge guiding right or left – center guiding Please contact the producer for any different application. Cover completely the sensors with the material to be guided! Target Tracking with B Tracking People with N When activating the opposite direction the alarm message will reset automatically. During start-up procedure, the total safety concept of the production ekd will have to be considered.
Cover the edge sensor completely, e. With a number of components that can be connected, the devices can be optimally adapted to their respective tasks in every case. When actuator EMS 6 will be employed, interchange the terminals 65 and 66 in addition.
Motor was switched off. Never clean the edge sensor with compressed air!
Dither OFF electric motor powered actuator? The indication of shifting occurred via EKR display. Operation The system only admits operation with the components actually present!
Close again the cover of the plunger coil regulator. The ekr digital unit touch impresses customers with its exceptional user-friendliness, ease of installation and use, and compact majual.
Maintenance The amplifier is maintenance-free. Emissions The A-rated equivalent continuous sound level of the equipment is lower than 70 dB A. Remove all material from the sensors and clean the lenses!
Assembly, installation and commissioning must be carried out by qualified personnel! With manuap FVG During 1050 seeking or after web tear, the inner limit switch was reached. Remove material from the sensor and clean the lenses! Clean lenses of the sensors and determine the contrast according to the graph below. For adjustment, remove cover of the ZT 6. Remote control Truth table for the remote control inputs EKR e.
Connect the second edge sensor with the second connection piece S1 and the connection piece marked S2. Slip the hose ends onto the corresponding connection pieces S1 and S2.