DATASHEET ADC0804 PDF

The ADC is a commonly used ADC module, for projects were an external ADC is required. It is a pin Single channel 8-bit ADC module. The ADC ADC ADC ADC and. ADC are CMOS 8-bit successive approximation A D converters that use a differential potentiometric. ADC Technical Data, ADCLCN 8-bit A/D Converter Datasheet, buy ADCLCN.

Author: Kajora Galrajas
Country: Tajikistan
Language: English (Spanish)
Genre: Education
Published (Last): 17 November 2008
Pages: 496
PDF File Size: 5.19 Mb
ePub File Size: 20.64 Mb
ISBN: 471-7-35243-135-2
Downloads: 5547
Price: Free* [*Free Regsitration Required]
Uploader: Grogal

The digital outputs vary from 0 to a maximum of Analog to digital converters find huge application as an intermediate device to convert the signals from analog to digital form. Analog inverting Input; normally ground. Data bit 0 to bit 7.

National Semiconductor

To set a particular voltage level as the reference value, this pin is connected to half the voltage. Seven output Data bit pins from which output is obtained. ADC is a very commonly used 8-bit analog to digital convertor. That is for every increase of Submitted by admin on 10 October Analog Ground pin connected to ground of circuit.

Skip to main content. This high-density System-in-Package SiP integrates controller, power switches, and support components. Only if this is done the ADC value on the output side will be update.

External clock can be connected here, else RC can be used for accessing internal clock. Input pin; sets the reference voltage for analog input.

  GIAMPIERI CARNIVAL OF VENICE PDF

Digital Ground pin connected to ground of circuit. Input pin; Low to high pulse is given to start the conversion. When this pin is not connected, the default reference voltage is the operating voltage, i. It is a single channel IC, i. Choosing Motor For Robots.

National Semiconductor – datasheet pdf

The chip select CS and Read R pin should also be grounded. RC timing resistor input pin for internal clock gen. An external clock can be given at the Clock IN pin. In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the Vin pin and the present Voltage is read using a voltmeter. It is a pin Single channel 8-bit ADC module.

ADC needs a clock to operate. Activates ADC; Active low.

Virgin Galactic — Commercial Space Flight. However to make the internal clock to work we have to use a RC circuit. Differential Analog input.

Connect to ADC input. Write pin should be pulsed high to start data conversion. Hence, if you are looking for a compact ADC module with a decent resolution of 8-bit then this IC is for you. Clock Input pin; to give external clock. The obtained value is 1. Reference voltage for ADC conversion.

ADC Datasheet(PDF) – National Semiconductor (TI)

What is Web Browser. TL — Programmable Reference Voltage. Or even to datashest as a standalone ADC module. Output pin; Goes low when conversion is complete.

  CREATING FILLABLE FORMS IN NITRO PDF

As you can see in the image the voltage value is 1. The time taken to convert the analog value to digital value is dependent on this clock source.

Interface SD Card with Arduino. Goes high for interrupt request. These digital signals are used for further processing by the digital processors. SPI Module of Arduino. Read pin must be grounded to ad0c804 the Analog value.

ADC also has an inbuilt clock which can be used in absence of external clock. Various sensors like temperature, pressure, force etc.

The step size can be adjusted by setting the reference voltage at pin9. Arduino based GPS receiver.

Choosing Battery for Robots. The step size at 5V is Interface GPS with Arduino. Chip select is used if more than 1 ADC module is used. Since the IC xatasheet with an internal clock we do not need many components to make it work. Used with Clock IN pin when internal clock source is used.