Buy Ideal Industries VFF5 Fiber Optic Visual Fault Finder: Electronics – Amazon. com ✓ FREE DELIVERY possible on eligible purchases. IDEAL NETWORKS | VFF5 | VFF5 Visual Fault Finder. Manufacturer # VFF5; Anixter # pdf Spec Sheet. Price per Each. Minimum Qty: Increments of: Qty. VFF5 Visual Fault Finder. Catalog # VFF5. Features q Finds Breaks, Faulty Splices and Crimps Poor Components or Connections q Low-Cost, Basic Fiber Test.
|Country:||Turks & Caicos Islands|
|Published (Last):||6 January 2005|
|PDF File Size:||13.73 Mb|
|ePub File Size:||20.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
The Visual Fault Finder is a visible laser light source used to check continuity, locate breaks, poor mechanical splices and damaged connectors in fiber optic cabling. Used to verify continuity, test and find breaks in fibre links, locate pinched fiber strands in termination cabinets, or anywhere fiber optic cables are terminated and subject to mechanical damage.
The VFF5 is also an excellent aide to technicians terminating mechanical splices or pre-polished connectors where leaking light is an indicator of a poor fiber cleave or other misalignment. A hand-held, battery-powered tool, the VFF5 projects a highly visible red light into a fiber optic cable.
Providing the finest test equipment solutions since 1992
The VFF5 is used to idal continuity of cabling between termination points and to locate bends or breaks in fibers at splicing and termination points. The VFF5 is useful over a distance of approximately 5km 3. Use it as a stand-alone first-line basic troubleshooting tool, or in conjunction with an OTDR to pinpoint faults.
Any breaks will be seen as a conspicuously glowing or blinking red light area in 3mm or smaller cables.
The VFF5 is equipped with a high-power, day light visible nm laser diode which operates either in continuous or flashing mode. The design prevents battery drain due to accidental activation of the tool while inside a tool pouch. Two AA batteries provide over 30 hours of operation in continuous mode and 80 hours of operation in flashing mode. The unit is packaged in a pocket-sized, rugged metal housing and is fitted with 2. The FC to LC adapter offers a simple solution to connect LC terminated cables with devices such as test equipment that does not have an LC connection option.
For quick checks of continuity and breaks, slip the adapter onto the VFF5 then slip the cable with the LC connector into the adapter. FC side is a threaded male connection that locks to female FC connectors on active network devices and test equipment. LC side is a friction-lock female connection that accepts male LC connectors found on LC patch cords. The compact size allows both simplex and duplex plugs to be used with the adapter.
Temporarily connecting LC terminated patch cords idwal test equipment for measurements. Because the LC portion is non-locking, the adapter should not be used as a permanent connection. Injecting visible light into connectors when terminating crimp-style connectors or when using mechanical splices for cable repair.
A proper termination will not leak excessive amounts of vfv5 from the connection. Additionally, aftermarket adapters are available that will convert a 2. Contact technical support if you have questions about where to obtain adapters or hybrid cables. There is no industry standard for the specification of light visibility of this class of device. Factors that affect viewable distance are battery life, type of fibre Iseal or SMfibre attenuation coefficient, fibre buffer and jacket colour, number of connectors in the link, and ambient lighting.
Under optimal conditions the viewable distance may increase to km 3. Visual fault finders in general have limitations to the type of cables the light is visible through. Typically 3mm standard simplex patch cords and smaller cable will allow the light to penetrate through the jacket when the fibre is bent, pinched or broken. However, the brightness is directly related to the colour of both the idal buffer and cable jacket.
Dark coloured buffers may absorb most of the leaking light and be difficult to see. Outside Plant Cable OSP is constructed with a heavy, black jacket that no type of visual fault finder will be able to penetrate if the break is mid-span this is a perfect application for the micro-OTDR.
However, these cables are usually damaged at the termination point where a fan-out kit is used. A break at this point would be easily visible.
Visual Fault Finder – VFF5
bff5 However this relates to the beam in “free space. For iideal reason, most fibre inspection scopes have infrared filters that protect the eye in these cases. However, care should always be taken not to look directly into the beam and to ensure that a fibre link is “dark” before looking into it with a microscope. Visually identifies and locates faults in fiber optic cabling 2. Overview The Visual Fault Finder is a visible laser light source used to check continuity, locate breaks, poor mechanical splices and damaged connectors in fiber optic cabling.
Testing of fiber continuity and locating bends or breaks in small fiber optic cabling. What type of connectors does the VFF5 accept?
vff55 How far away can the light from the VFF5 be seen? Can the VFF5 detect breaks in any type of cable? Is it dangerous to look into the laser beam? Message is a required field, please fill it in.
Please keep me up to date with the latest product news.